The Electron Series is a Revolutionary Tankless Heat Pump. The FIRST and ONLY Electric Heat Pump Water Heater to Deliver Reliable and Safe Hot Water Without Storing Any Water.
Under the Hood of Our Electron
Series Water Heaters
The electron is an air source heat pump that absorbs heat from the air and stores it in a specially designed thermal battery. This thermal battery contains a special blend of a water-glycol mix for heat storage along with a unique tankless heat exchanger built inside. When there is a demand, domestic water flows through this heat exchanger and is heated to precisely the right temperature, and is available for use immediately. The absence of storage tanks allows us to provide a Legionella Free Guarantee and a limescale-proofed system.
Electron (CO2 Heat Pump Water Heater) FAQ
No, mixing valves will not be required. The Electron series water heaters will be ASSE – 1082 compliant. The ASSE-1082 standard equates Electron Series Tankless Heaters to thermostatic mixing valves and temperature-limiting devices. Also, the Electron can control water temperature within the tolerances of ASSE 1017 / 1071 standards, and thus, no mixing valves when using Electron units.
The Electron series has a modular design to facilitate fast service and enable customers to run their businesses efficiently. The Heat Pump Units (HPU) on Electron Series are designed to be easily swapped with a reconditioned HPU unit. Just two fluid connections and two wiring connections are all that need to be made. There is no field repair, refill of CO2, or handling of high pressures required in the field. The faulty HPU can be sent to an authorized Intellihot service center, where it will be repaired under a controlled and non-emergency environment.
Electron products are built to last and feature a robust modular design. All parts, including the compressor, are warrantied for one year, and the thermal battery and on-demand heat exchanger are warrantied for three years. All warranties are from the date of commissioning.
Model iE1 with the integrated Thermal Battery has a maximum heating output of 90,000 BTU/h. Model iE6, the modular unit, has a heating capacity of up to 300,000 Btu/h. However, it may be paired with four thermal batteries, bringing its total heating capacity up to 800,000 Btu/h.
Model iE1 has an airflow requirement of 3,500 CFM and can be installed indoors or outdoors. Model iE6 has an airflow requirement of 21,000 CFM high and should be installed outdoors only
We have developed a simple and easy way to cascade multiple units without running wires. This is achieved through a Bluetooth connection like those in smartphones. Units have a maximum communication distance of 50 ft, and it is recommended to have a direct line of sight without any metal obstructions.
The Electron series is designed for long life and low maintenance. Only one item needs to be serviced at internals indicated by “maintenance alert” on the display. This is the Wye strainer which prevents large debris in the water supply from entering the unit. The unit has sophisticated prognostics capability, and the life of critical components is shown on the “Life Screen .”It provides guidance for when these parts should be changed.
The Thermal Battery is designed to last a lifetime under normal wear and tear. The battery is designed with high-grade stainless-steel components and factory-supplied food-grade propylene glycol. This food-grade glycol can be safely disposed of in a regular drain. The Thermal Battery can be sent to a typical metal recycling facility. Non-biodegradable glycol, especially ethylene glycol (e.g., automotive grade) or non-Intellihot supplied formulations, should never be used to charge the Thermal Battery. Doing so may cause irreparable damage and bodily harm, including death.
Each location in the county could have a different minimum ambient temperature. Thus, the Thermal Battery can accommodate various concentrations of propylene glycol. The Thermal Battery has a Glycol Concentration Sensor built-in which, in correlation with the zip code of the installation, verifies the concentration specific to that location. If inadequate, a message will pop up on the display. When a unit is ordered for drop shipment, the appropriate volume of glycol will be prefilled at the factory based on the zip code. The cost for this will be billed separately. In addition, glycol kits will also be available for purchase for use in the field.
Model iE1 runs on a single phase 208V AC with a maximum current draw of 75A. A dedicated 90-ampere breaker is required for this model. Model iE6 runs on a three-phase 208V AC with a maximum current draw of 75A. Three separate but dedicated 90-ampere breakers are necessary for this model. Model iB3 (modular thermal battery) runs on a three-phase 208V AC with a maximum current draw of 75A. Three separate but dedicated 90-ampere breakers are required for this model.
The inside components of Models iE1 and iE6 are freeze protected. When the model iE1 is installed outdoors, the external domestic water lines should be appropriately insulated and heat traced.
The iE1 and the iB3 have a patented leaking sensor built-in. This leak sensor distinguishes between a glycol leak and a domestic water leak and drives appropriate control action. For example, if there is a domestic water leak, then the unit will automatically shut down the water inlet to the unit. If there is a glycol leak, then the unit will shut down. Warnings and notifications are sent via the telliCare app.
Typical heat pumps use storage tanks and deliberately keep the domestic water stratified at various temperatures. Stratification is needed to enable the heat pumps to operate efficiently. Stagnation and water temperature being in the growth range of Legionella pose a substantial risk. The Electron series does not store any water, heats on-demand, and has water velocities that are 400 times higher than a tank, thus mitigating biofilm formation and reproduction of Legionella bacteria. This results in good, safe, clean, and efficient hot water.